You can overcome the email sending issues by using the following email relay settings.
====
cPanel Servers
====
Login to WHM Panel
Navigate to the “Smarthost support” section of WHM’s [Home »Service Configuration »Exim Configuration Manager], then add the relay server’s IP preceded by an asterisk.
So in our case:
Smarthost support
* 109.201.130.65
We might need to make changes on the SPF record. Replace the current server IP address and add the relay IP.
eg: v=spf1 a mx ip4:109.201.130.65 ~all
===
ISP Manager Panel – Exim
===
Assuming you’re installing the yum version of Exim on a CentOS server, you’ll need to make two configuration changes. The first is to allow the IP of the mailserver to relay through the smarthost. Open the configuration at /etc/exim/exim.conf, find the line referenced below and edit it by adding the relay server IP 109.201.130.65 at the end as shown below.
hostlist relay_from_hosts = 127.0.0.1
eg: hostlist relay_from_hosts = 127.0.0.1 : 109.201.130.65
Then, uncomment and change the smarthost section in exim.conf under ‘begin routers’ line like below:
smarthost:
driver = manualroute
domains = ! +local_domains
transport = remote_smtp
route_list = * 109.201.130.65
no_more
no_verify
Save the modified config file and restart Exim on this server. That’s it;
====
Exim Mail Server(Servers without cPanel)
====
Assuming you’re installing the yum version of Exim on a CentOS server, you’ll need to make two configuration changes. The first is to allow the IP of the mailserver to relay through the smarthost. Open the configuration at /etc/exim/exim.conf, find the line referenced below and edit it by adding the relay server IP 109.201.130.65 at the end as shown below.
hostlist relay_from_hosts = 127.0.0.1
eg: hostlist relay_from_hosts = 127.0.0.1 : 109.201.130.65
Second, you’ll need to tell Exim not to listen only on the localhost address for incoming mail, which is the default. Again find the configuration line below and add a hash (#) in front of it to comment it out.
local_interfaces = <; 127.0.0.1 ; ::1 eg: #local_interfaces = <; 127.0.0.1 ; ::1
In some exim versions, there is no ‘local_interfaces’ field. In such cases, just ignore this step.
Third, uncomment and change the smarthost section in exim.conf like below:
smarthost:
driver = manualroute
domains = ! +local_domains
transport = remote_smtp
route_list = * 109.201.130.65
no_more
no_verify
Save the modified config file and restart Exim on this server. That’s it;
====
Postfix Mail Server
====
Open your postfix configuration:
vi /etc/postfix/main.cf
find the line ” relayhost ” inside the configuration and add the IP 109.201.130.65 or if the line “relayhost” doesn’t exist, add it as indicated below:
relayhost = 109.201.130.65
Save the changes by pressing ESC+ :wq
Then restart the postfix service
service postfix restart
Check the mail working and you are done.
====
Qmail (Kloxo Servers)
====
Open the following Qmail configuration file:
/var/qmail/control/rcpthosts
Add the following text inside it:
109.201.130.65:allow,RELAYCLIENT=””
Then save and exit.
Open another configuration file:
/var/qmail/control/smtproutes
Add the following on it:
:109.201.130.65
Then save and exit.
Restart the xinetd and qmail services:
/etc/init.d/xinetd restart
/etc/init.d/qmail restart
And we are done!
==========================
We might need to make changes on the SPF record. Replace the current server IP address and add the relay IP.
eg: v=spf1 a mx ip4:109.201.130.65 ~all